Multitherm® Heat Transfer Fluids Products

Heat Transfer Fluids: High Temperature Applications

MultiTherm PG-1®

 Physical Properties
 FDA Certification
 MSDS Sheets
  • Operating range from 10°F (-12°C) to 600°F (315°C)
  • Food grade (NSF registered, FDA certified Non-Toxic, USDA Chemicallyacceptable, Kosher certified)
  • Low viscosity / Low pour point
  • Non-Toxic, Non-Hazardous, Non-Fouling
  • Designed for applications in Food, Chemical, Plastics, and Die-Casting
  • Thermal expansion coefficient 0.00035/ºF (0.00063/ºC)
  • For use in closed loop, liquid phase heating and cooling systems to 600°F

MultiTherm OG-1®

 Physical Properties
 MSDS Sheets
  • MultiTherm's oxidation grade fluid for open or closed loop systems
  • Operating range from 10°F (-12°C) to 550°F (290°C)
  • Highly refined to have High flash point
  • Oxidation resistant - Very Low vapor pressure
  • Non-Toxic, Non-Hazardous
  • Designed for applications where the hot heat transfer fluid comes in contact with atmosphere
  • Thermal expansion coefficient 0.00056/ºF (0.00102/ºC)


MultiTherm 503®

 Physical Properties
 MSDS Sheets
  • When you have heating and cooling in the same loop
  • Operation range: from 50°F (-10°C) to 500°F (260°C)
  • Meets FDA specifications but not certified
  • Very low viscosity - Very low pour point - Low vapor pressure
  • Relatively high flash point - Non-Toxic, Non-Hazardous
  • Designed for applications in Plastics, Chemical, and other processing industries
  • Thermal expansion coefficient 0.00051/ºF (0.00092/ºC)
  • For use in closed loop, liquid phase heating and cooling systems from 10°F to 500°F


MultiTherm IG-4®

 Physical Properties
 MSDS Sheets
  • Operating range from 10°F (-12°C) to 600°F (315°C)
  • Highly refined to have High flash point
  • Oxidation resistance - Very Low vapor pressure
  • Non-Toxic, Non-Hazardous
  • Designed for applications in Asphalt, Chemical, Plastics, Laundries and Die-Casting
  • Thermal expansion coefficient 0.00054/ºF (0.00097/ºC)
  • For use in closed loop, liquid phase heating systems up to 600°F
  • MultiTherm IG-4 is an upgrade of, and a direct replacement for MultiTherm IG-2®


MultiTherm IG-1®

 Physical Properties
 MSDS Sheets
  • Operating range from 10°F (-12°C) to 550°F (288°C)
  • Economical heat transfer fluid
  • High flash point
  • Non-Toxic, Non-Hazardous
  • Designed for applications in Asphalt, Roofing, Paper, Particle Board and Die-Casting
  • Thermal expansion coefficient 0.00054/ºF (0.00098/ºC)

Heat Transfer Fluids: Low Temperature Applications

MultiTherm ULT-170®

 Physical Properties
 MSDS Sheets
  • For ultra low temperature applications
  • Operation range down to -170°F (-112°C)
  • Low freezing point - Low viscosity at ultra-low temperatures
  • Thermally stable & biodegradable
  • Single fluid usage for sterilization applications
  • Designed for Pharmaceutical, Chemical, Freeze-Drying, and Cryogenic applications
  • Extends low-end operating ranges far beyond the boundaries of most competitive brands
  • Remains pumpable even at temperatures below -170°F (-112°C)

 

MultiTherm WB®

 Physical Properties
 MSDS Sheets
  • Aqueous-based for Low temperature applications
  • Operation range down to -58°F (-50°C)
  • Non-toxic, None-flammable
  • Designed for Ice Rink, Food, Refrigeration, Breweries/Distilleries, and HVAC applications
  • Engineered to deliver the desirable low-end temperature performance of synthetic organic and silicone-based fluids

Heat Transfer Flushing/Cleaning Fluid

MultiTherm FF-1®

 Physical Properties
 MSDS Sheets
  • Specially formulated flushing fluid to clean out systems during:
    • Start-ups - to remove loose material such as weld splatter, fines, particulate matter, etc. left in lines and equipment, along with oil and some preservative coatings
    • General Maintenance - for removing particulate matter and used heat transfer fluid from a system prior to recharge or changeover from one fluid to another.
  • Compatible with all MultiTherm and mineral oil heat transfer fluids.
  • Thermal expansion coefficient 0.00047/ºF (0.00085/ºC)

MultiTherm PSC Plus®

 MSDS Sheets
  • Specially formulated flushing fluid to clean out systems during:
    • Start-ups - to remove loose material such as weld splatter, fines, particulate matter, etc. left in lines and equipment, along with oil and some preservative coatings
    • General Maintenance - for removing particulate matter and used heat transfer fluid from a system prior to recharge or changeover from one fluid to another.
  • Compatible with all MultiTherm and mineral oil heat transfer fluids.
  • Thermal expansion coefficient 0.00047/ºF (0.00085/ºC)

Heat Transfer Filtration
Hot Oil Filtration Systems

 Hot Oil Filtration Systems
Hot oils degrade by thermal cracking and oxidation. The two by-products of oil degradation is sludge and coke due to carbon build-up. These products can collect through-out your system but specifically in pump seals and internals, valves, etc. that result in equipment problems and possibly eventual system breakdown.

HVAC/Industrial Coils

Replacement or New

 Hot Water Coils
 Evaporator Coils
 Steam Coils
 Chilled Water Coils
 Refrigerant Condensor Coils
 Hot Water Duct Booster Coils
 Industrial Coil Construction
Chilled Water, Hot Water, Steam, DX or Condenser

Heavy duty industrial coils of all types
  • Duplicate existing dimensions and performance
  • Special 5 work day and 10 work day quick shipments available
  • Hot water duct booster coils in stock
  • Call 800-225-7440 for immediate pricing, technical information and delivery information

T-Bar Self Contained AC Units

T-Bar Self Contained AC Units

 Air Cooled - Grille Diffuser
 Air Cooled - Single Duct
 Air Cooled - Double Duct
 Water Cooled - Grille Diffuser
 Water Cooled - Single Duct
 Water Cooled - Double Duct
 Chilled Water - Grille Diffuser
 DX Grille Diffuser
A T-Bar Unit from Multitherm® is the answer to your special cooling and dehumidification needs. And, it fits right into a standard 2' x 4' suspended ceiling panel, with no floor space needed.

 

 

JUNIORFLUX Pump & Motor Unit/PP From MultiTherm

 JUNIORFLUX Pump & Motor
For filling, emptying, transferring or dispensing small amounts of liquid out of carboys, hobbocks, canisters, narrow-necked containers or barrels FLUX now offers a better performance: the new JUNIORFLUX pumps type F 310 and F 314.

The JUNIORFLUX pumps are available in polypropylene (PP), polyvinylidene fluoride (PVDF) or stainless steel (S), both in version with mechanical seal Type F 310 or sealless Type F 314.


A powerful 230 Watt commutator motor with a 2-speed switch allows sensitive, fast and therefore low-cost and safe filling operations. The motor is built to protection class II, splash-proof and comprises an overload cut-out switch. Another feature is the modern and ergonomically structured design for single-hand operation.

 

 



 

 


Multitherm® Products