Options, Enhancements, Kason Vibroscreen

Options/Enhancements For Kason Vibroscreen®

Process Controls Index
General
Kason Products
K-Tron Products
Littleford Day Products
Sturtevant Products
Western States
Abanaki Products
  Kason Screeners, Centrifugal Screeners and Fluid Bed Dryers/Coolers for bulk materials
Options, Enhancements, Kason Vibroscreen
 

 

Designs for Sanitary Applications

 

Options, Enhancements, Kason Vibroscreen
All VIBROSCREEN® circular vibratory screeners from 18 to 100 in. (460 to 2540 mm) in diameter are available designed, constructed and finished to industrial, food, dairy and pharmaceutical standards including FDA, 3-A, USDA, BISSC and others. Sanitary screeners generally incorporate rounded corners, continuous ground and polished welds, domed lids, quick-release "U" clamps, and 4-post open bases with stainless steel motor enclosures allowing thorough wash   down of the underside and plant floor. Sanitary screeners generally offer one or more of the following features:

 

'Air-Lift' Quick Screen Change System

 

"Air-Lift" Quick Screen Change System

 

Kason's Air-Lift quick screen change system for circular vibratory screeners allows operators to change screens and gain access to the interior of the unit for cleaning or inspection many times faster than possible using comparable systems.

The lightweight device consists of two vertically mounted air cylinders that are located on opposing sides of any circular separator and affixed to mounting brackets on the lower and upper screening frames.

To operate, a quick-disconnect clamp connecting the frames is removed and a remote air valve is actuated, raising the upper frame. The procedure is reversed to reconnect the frames.

One entire raise/lower cycle including quick-disconnect/connect of the frames, requires only several minutes, reducing downtime during every inspection,

 

cleaning and screen-changing operation. In addition, one operator can now perform what was previously a two-person task, depending on screen diameter.

Other safety features include a safety lock-out that locks the frames in the open or closed position when the upper screener housing is raised or lowered, and safety bars that prevent the housing from accidentally descending while in a fully-raised position during screen changes or wash down.

The Air-Lift device is available on any new Kason screener, and can be retrofit to any circular vibratory screener of any make or model from 48" to 84" (1220mm to 2135mm) in diameter, including screeners having single- or multiple-decks, and screens with or without center holes and/or anti-blinding devices.


'Clamshell Lid' Quick Screen Change System

 

"Clamshell Lid" Quick Screen Change System

 

All Vibroscreen® separators from 30" to 84" (760mm to 2135mm) diameters in both single- and multi-deck configurations are available with Kason's exclusive "clamshell" option. The hinged lid and/or frames are released via quick-disconnect clamps and held in an open position by gas pistons, allowing rapid screen changes and easy, thorough

 

washdown of all interior surfaces. The Clamshell Lid accepts screens with or without center tensioning construction, and accommodates screen decks with or without anti-blinding devices. The Kason Quick Screen Change Assembly is the only deck-opening device offering all of the above capabilities.

Clean-In-Place (CIP) Design, Construction and Finish

 

Clean-In-Place (CIP) Design, Construction and Finish

 

Vibroscreen® vibratory screeners designed, constructed and finished to Clean-In-Place (CIP) specifications employ spray nozzles that are strategically placed to emit cleaning solutions, rinsing solutions and/or steam for sanitizing the interior of the screening chamber(s) without the need to open or otherwise disassemble the unit. The perforated, ball-shaped, stainless steel nozzles are positioned at the end of stainless steel pipes that extend outward from the screen deck frames and upward from the top surfaces. Their flanged connections ensure leak-free connection to hoses


 

carrying cleaning solution. Quick-disconnect clamps allow two-minute disassembly of all water supply hoses, clean-in-place spray head fittings, and screener body sections for inspection or screen changes. Unlike traditional circular vibratory screeners, CIP screener frames and screens are designed to eliminate the gap that normally exists between the mounted screen and the frame wall. CIP screeners are offered in diameters from 18 to 60" (460 to 1525mm) in all-stainless construction finished to FDA as well as 3-A, BISSC and other sanitary standards.

Design, Construction and Finish to Pharmaceutical Specifications

 

Design, Construction and Finish to Pharmaceutical Specifications

 

Vibroscreen® vibratory screeners for pharmaceutical applications feature clean-in-place spray heads for hands-free wash down. The pharmaceutical screener shown is configured with one gap-free screening deck. Three clean-in-place spray heads are required: one each for the upper, central and lower chambers. Quick-disconnect clamps allow two-minute disassembly of all water supply hoses, clean-in-place spray


 

head fittings, and separator body sections for inspection or screen changes. Unlike traditional circular screen separators, this sifter has no gaps between the mounted screen and the frame wall. It is offered in diameters from 18 to 60" (460 to 1525mm) in all-stainless construction finished to FDA as well as 3-A, BISSC and other sanitary standards.

Gap-Free Design

 

Gap-Free Design

 

This Kason innovation features an interlocking flange between screen frames that protrudes from the external side of the frame to fully envelop the circular support ring of the internal screens. This enables the mesh of the screen to fully extend to the walls of the frame, eliminating the gap between the screen ring and frame wall of conventional screeners where material typically collects. The gap-free design dramatically reduces the possibility of contamination due to bacteria growth,

 

while improving sanitizing efficiency, making it suitable for pharmaceutical, food and dairy applications as well as chemical applications where cross-contamination is a concern.

Screens are mounted to support rings using FDA-approved epoxy and sealed using FDA-approved gasket material. The wire mesh screening material is offered in 304, 316 and "magnetic" 400-series stainless steel that, if broken, can be captured by a downstream magnet.


E-Z FORCE™ Weight Adjustment System

 

E-Z FORCETM Weight Adjustment System

 

The E-Z FORCE weight adjustment system allows precise control of material flow patterns. The high torque, high-efficiency, imbalanced weight gyratory motor, which is rigidly mounted to the screening assembly, has a double


extension shaft fitted at each end with variable eccentric weights. Weights can be adjusted in several minutes by one operator, allowing maximum efficiency for each screening application.

Ball Tray Anti-Blinding Device
 

 

Ball Tray Anti-Blinding Device

 

The Kason Ball Tray Anti-Blinding Device utilizes the multi-plane inertial vibration of the screener and bouncing elastomeric balls to prevent screen blinding. The device consists of two screens spaced sufficiently apart to allow captive elastomeric balls to bounce between the upper "operating" screen and the lower coarse-mesh "ball screen" for the purpose of dislodging near-size, dry materials lodged in the apertures of the upper screen.

Kleen Screen Anti-Blinding Device
 

 

Kleen Screen Anti-Blinding Device

 

Kason Kleen-Screen Rings are effective at preventing fibrous, stringy and sticky materials from blinding the screen. Multi-plane inertial vibration of the screener causes plastic rings to move continuously across a perforated stainless steel plate, shearing fibers and scraping away gummy materials. Because they are hollow, the rings promote product flow over the entire screen surface, maximizing screening efficiency.

Ultrasonic Anti-Blinding Device for fine powders
 

Ultrasonic Anti-Blinding Device for Fine Powders

 

The patented Kasonic® anti-blinding device allows sifting as fine as 25 microns (500 mesh) on any circular vibratory screener of 18" to 100" (460mm to 2540 mm) diameter. It transmits ultrasonic frequencies (adjustable) to the

 

screen, adjusting power automatically according to screen loads. It operates with standard screens, reducing cost, and is supported independent of the screen, prolonging screen life.
   

Auto-Lube Automatic Lubrication System for Gyratory Motors

 
Auto-Lube Automatic Lubrication System for gyratory motors
 

The imbalanced weights in gyratory screener motors subject bearings to extreme loads, with inadequate or improper lubrication resulting in rapid bearing wear—the major cause of gyratory motor failure. Kason's Auto-Lube automatic lubrication system is designed to eliminate this problem by pressure feeding lubricant into motor bearings for 6 to 12 months between


 

reservoir replacements. Continuous lubricant flow flushes the race of wear materials, broken down lubricant and contaminants, and minimizes dead spots where up to 95 percent of the lubricant would otherwise remain unused. Optional on Vibroscreen separators in 48" (1220mm) and larger diameters. Can be retrofit in one hour to any circular vibratory screener.

Wiper Blade Assembly
 
 

Wiper Blade Assembly

 

The wiper blade assembly prevents screen blinding and boosters capacity by breaking down lumps and agglomerates. The independently mounted assembly allows adjustment of

 

wiper blade height above or at the screen surface, and adjustment of blade speed from 1 to 15 RPM. Rubber wiper blades or bristle brushes can be affixed to agitator shaft arms.

Four-Finger Flex Wiper Anti-Blinding Device
 
 

Four-Finger Flex Wiper Anti-Blinding Device

 

The Four Finger Flex Wiper anti-blinding device employs four radial arms of durable neoprene to prevent screen blinding of the operating screen by slimes, pitch and other soft, gummy materials. Multi-plane inertial vibration of

 

the screener causes the wipers to rotate continuously, enhancing the flow of material through apertures of the screen. Specially designed units are available for exceptionally difficult-to-screen products.

Bag Dump/Dust Collector configurations Bag Dump/Dust Collector configurations
 

Bag Dump/Dust Collector Configurations

 

Kason gravity-fed and pneumatic in-line screeners in 24", 30" and 40" (610, 760 and 1015mm) diameters are available configured as basic Bag Dump Stations (top), or Bag Dump Stations with Dust Collectors (bottom) that protect the operator and plant environment against dust contamination during manual dumping operations. Ambient air and dust from dumping activities is drawn onto the exterior of two cartridge filters that derive vacuum from a top-mounted exhaust fan. Dust accumulated on the filters' exterior surfaces is dislodged by overcoming continuous negative pressure within the cartridge filters, with positive pressure introduced in short blasts on a timed cycle by pulse jet

 

nozzles. Dislodged material falls into the screener while instant resumption of negative pressure collects any dust generated by the filter cleansing operation. To afford a sufficiently low deck height for manual dumping—and provide space below the screener outlet for connection to mechanical or pneumatic conveyors, process equipment or storage vessels—bag dump stations are normally specified in combination with Kason's Flo-Thru low profile screener. Screeners configured for bag dumping with or without dust collection are available to industrial, food, dairy and pharmaceutical standards including 3-A, FDA and BISSC.

See-Through Dust Cover
 
   

See-Through Dust Cover

Flexible, transparent dust covers allow visual inspection of material flow patterns on the upper screen, provide easy access to the screen, and prevent contamination during shut-down.

 

 

High Capacity 'KASCADE' Internal Recycle Screening Decks
 

High Capacity "KASCADE" Internal Recycle Screening Decks

"KASCADE" Internal Recycle Screening Decks operate in conjunction with conventional screening decks to increase the capacity of new or existing circular vibratory screeners by 60 to 160 percent.

Available new or as retrofit kits, KASCADE screening decks are generally specified for new applications where space is restricted since diameters are significantly smaller than those of conventional screeners having equivalent capacity, or for retrofit applications to increase capacity and efficiency (minimized "carry-over" and ejection of on-size material) at substantially lower cost than purchasing new equipment.

Positioned directly above conventional screening decks, a KASCADE deck has a screen of identical mesh, but of slightly smaller diameter than the conventional screen below, allowing for a 360° annular gap at the screen's periphery.

The KASCADE deck is fed with more material than it can efficiently screen, with two results: 1) On-size material falling through the screen of the KASCADE deck is funneled through a hole in the center of the lower conventional screen to the machine's discharge outlet, and 2) The overflow of on-size material plus all oversize material cascade over the screen's periphery, onto a conventional screen of equal mesh that scalps the balance of material in normal fashion.

Kason offers KASCADE screening decks in one-, two-, or three-deck configurations (single-deck shown), in diameters from 40" to 100" (1025mm to 2550mm) to scalp, dedust, and/or classify up to 91 metric tons/h of free-flowing bulk material.

Available to 3A, USDA, FDA, BISSC and other sanitary standards, KASCADE screening decks can be disassembled rapidly for thorough wash-down.



Site Design: Process Controls And Instrumentation