| Process Controls Home |
|
|
 |
| Products |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| General Information
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 Scarsdale Road
Don Mills ON M3B 2R2
Toll Free: 1 800 465-1600
|
|
|
| Manufacturers |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Data
Track Tracer 212 Process And Temperature Indicator
|
Acquisition • Measurement • Control
The new Tracker 212 is an all-in-one, attractively designed and priced unit. It has been engineered as a universal process and temperature indicator with user linearization features for
4-20 mA signals.
• Low Cost with a 5 Year Warranty
• Quick and Easy to Configure
• 24-Point User Linearization for 4-20 ma Signals
• Universal Process or Temperature Measurement
• Sensor Excitation for Transducers (10V) or Two Wire Transmitters (24V)
• Selectable Degrees F or C
• Display Scaling To Any Engineering Units
• 12-32 VDC/VAC Powered Version Option
• Universal Mains Power Input (110-250 VAC)
• Scalable Isolated Analog Output Option
• PC Programming Option
• Alarm Relay Fitted As Standard
• 2nd & 3rd Alarm Outputs Option
• No Internet Pots, Links or Plug In Cards
• Accepts mV, ma, V Ohm Signals Plus Type J,K,N,T,R,S Thermocouple and PT100
Outputs
The T212 is fitted with a relay output with volt free C/O contacts, as standard. The alarm can be high or low acting with user selectable hysteresis and with the relay configurable to be
energized or de-energized (fail safe) when in the alarm condition. Two further alarm relays can be fitted as an option.
The analog output option gives an isolated 4-20 ma signal, which is scalable to any portion of the display range. The output is linear to the displayed value, not the input. This makes the
Tracker 212 an ideal tank contents transmitter.
 Data
Track Tracker 212 Process And Temperature Indicator
|
|
System
7000 StrainSmart Data System
|
 Digital Data Acquisition System:
• Acquires data from measurements
• Stores acquired data
• Reduces data to meaningful units
• Presents reduced data for viewing
Design Concepts:
• Versatile Performance - Multiple sensors (strain gauges, strain-gauge-based transducers, high-level voltage signals and thermocouples).
• Self Calibrating - Removable NIST-traceable calibration standard in each unit
• Distributed System - Multiple data acquisition units can be located near sensors to reduce cable costs
• StrainSmart Based - Next generation hardware for StrainSmart software
• Ethernet Network Architecture - Low latency inter-channel communications for input response and near real-time data viewing
• High Channel Density - 128 channels in a 19-in x 4U box
• Latest Technology Hardware - 24-bit Delta-Sigma ADC, on-board DSP's and Compact Flash data storage
• DC Operation - 11 to 32 VDC, AC adapter available
Performance Features:
• Circular buffer of up to 800,000 samples per channel
• Simultaneous sampling
• Scanning rates up to 2048 samples/second/channel for all channels
- Radix 10 sampling rates
- Radix 2 sampling rates
• Dedicated Compact Flash non-volatile memory for each input and output card
- Maximum of 2GB storage (1GB standard)
• Separate high speed communications busses
- Synchronous data bus
- Asynchronous command bus
• Distributed System
- Scalable from 8 to thousands of channels
- Multiple 128 channel scanners per system
- Up to 100 meters between scanners (when synchronized)
• High Channel Density
- 8 channels per input/output card
- 128 channels per scanner
- Height: 4U, Width: Rack mountable in 19 inch cabinets (128-channel box)
Network Architecture
• Ethernet Interface
- IEEE 802.3, 802.3u, 10Base-T, 100Base-TX, half and full-duplex, auto-detect
 System
7000 StrainSmart Data System
|
|
|
Celesco's miniature MLP series linear potentiometers offer unrivaled performance in an amazingly small size. Though small,
the MLP is environmentally robust, operates over a broad temperature range and has a cycle life greater than 25 million cycles.
DASH
8Xe Data Acquisition Recorder