Nex Flow Products
Site Search Engine
2 Inch Air Edger Flat Air Nozzle Model 47011-4
2" Model 47011-4 Air Edger Flat Air Nozzle
The Model 47011-4 Air Edger Flat Air Nozzle, provides a powerful force while reducing compressed air use for a variety of blow off applications. The unit is 2" wide and the gap is maintained by a shim. Changing or stacking various shim sizes allows you to set the force that you need for any particular application - from a light blow off to a powerful blow off force.
The Model 47011-4 Air Edger Flat Air Nozzle are easy to mount and maintain, reducing both compressed air consumption and noise levels.
The Model 47011 Air Edger Flat Air Nozzle is made of Cast Zinc. The Model 47011S Air Edger Flat Air Nozzle is made of 316L Stainless Steel.
The Model 47011-4 Air Edger Flat Air Nozzles work by producing a laminar flow of air along its 2" length using the "Coanda" effect which entrains a large volume of air from the surrounding area along with a small amount of compressed air from the Air Edger Flat Jet Air Nozzle itself to produce an amplified output flow. Made of cast zinc aluminum it is a rugged unit applicable for many applications. Units may be placed side by side to provide an efficient and strong blowing force over wide lengths.
How it Works:
Compressed air enters the flat jet at the rear port at (A). Air is entrained at point (B) and (D) by the compressed air stream that leaves the flat air nozzle from a small gap at the end. The entrained air follows the profile that directs the airflow in a perfect straight line to create a uniform sheet of air along the 2" length of the Air Edger Flat Air Nozzle. The amplified air stream maximizes velocity and force to produce a well-defined sharp edge laminar flow with minimal wind shear for reduced energy use in blow off and cooling. Two screws at (C) allow you to vary the gap with a variety of sizes of shims (.004", .008" or .020"). One or two shims may be used.
Nex Flow Air Edger Flat Air Nozzles
Model 47011 Air Edger Flat Air Nozzle is an extremely efficient flat jet air nozzle designed to provide a powerful stream of high velocity laminar flow and high force for blow off and cooling where air knives may not be enough.
When bench tested against several other flat jets, even those with special designed holes or shims, the Air Edger Air Nozzle outperformed them all despite whatever claims others may make. Air consumption and noise levels are minimized with its special design and configuration.
The Nex Flow Air Edger Air Nozzle is available with various size "gaps" all set by a flat shim. Three standard shim sizes are available - .004" (.10 mm), .008" (.2mm) and .020" (.51 mm). One, two or more shims can be "stacked" for a larger gap and greater force.
If you are not sure of which level of power you need, we recommend a Model 47211S Shim Set consisting of 2 - .004" shims, 2 - .008" shims and 1 - .020" shim and any two shims (or more) can be stacked to set the gap best suited to your application.
Air Consumption And Force
Compared To Competition
It is not always clear how tests and measurements are made by competitors and therefore validating claims can be difficult since such values depend on how tests are done. Therefore we measured a competitive unit under the same conditions as we measured our units. The flat jet of the competitor is of a similar type except that they are using a saw tooth shim design and different internal dimensions. We obtained the following readings when measured using the same parameters as for Nex Flow units.
22 SCFM - 22 oz force 25.1 SCFM - 15 oz force
The force/SCFM is a ratio of .54
One measure of efficiency is the ratio of Force/Air Consumption. The higher the ratio the better the efficiency.
If we compare to that of the Nex Flow Model 47011-4 the ratio is 12/20.5 = .58
In both cases the efficiency of the Nex Flow units are higher in the comparative tests done. Under the same conditions.