Panel Cooling Systems | Cabinet Panel Coolers

Panel cooling systems are used in industrial, computing, networking, and other applications where thermal management of electronics and power supplies is important.

Cabinet panel coolers remove the heat generated by electronic devices from the inside of cabinets or enclosures, typically employing a refrigeration cycle.

Cabinet panel cooling systems are manufactured in many varieties of mounting styles, cooling capacities, and power configurations.

Frigid-X™ Cabinet Panel Coolers

General introduction to Nex Flow Frigid-X Cabinet Pnel Coolers.

<< Learn More >>

Frigid-X™ Cabinet Panel Coolers

Frigid-X™ NEMA 3R (IP 14) Cabinet Panel Coolers

NEMA 3R (IP 14) Cabinet Panel Coolers for outdoor use. Stainless steel to hold up to rain, snow, humidity and general outdoor use.

The NEMA 3R Cabinet Panel Coolers provides a low cost method of both purging and cooling electrical and electronic control panels by using a stainless steel vortex tube to create cold air from ordinary compressed air.

<< Learn More >>

Frigid-X™ NEMA 12 (IP 54) Cabinet Panel Coolers

NEMA 12 (IP54) Cabinet Panel Cooler for electronic control panels for general use in industrial environments where no direct liquid spray is applied to the unit. Stainless steel construction to hold up in corrosive environments.

The NEMA 12 (IP54) Cabinet Panel Cooler provides a low cost method of both purging and cooling electrical and electronic control panels by using a stainless steel vortex tube to create cold air from ordinary compressed air

<< Learn More >>

Frigid-X™ NEMA 4-4X (IP 66) Cabinet Panel Coolers

NEMA 4-4X (IP66) splash resistant, Stainless Steel Cabinet Panel Coolers for use in wash down environments as well as outdoor use. Unique patented design for secure water tight protection. Stainless steel for food service and corrosive environments. Stainless steel also provides for long life in wet environments and for outdoor use.

The NEMA 4-4X (IP66) Stainless Steel Cabinet Panel Coolers provides a low cost method of both purging and cooling electrical and electronic control panels by using a stainless steel vortex tube to create cold air from ordinary compressed air.

<< Learn More >>

Frigid-X™ 316L Stainless Steel NEMA 4-4X-316L (IP66) Cabinet Panel Coolers

Frigid-X™ Stainless Steel Panel Coolers NEMA Type 4-4X-316L (IP66), all external exposed surfaces are of 316L and ideal for pharmaceutical industry and extreme corrosive environments where 303/304 stainless steel is not adequate. As with the NEMA Type 4-4x Cabinet Panel Coolers, the cooler is splash resistant, for use in wash down environments as well as outdoor use. Unique patented design* for secure water tight protection. 316L Stainless Steel for pharmaceutical grade, food service and extreme corrosive environments. Stainless steel also provides for long life in wet environments and for outdoor use.

<< Learn More >>

Frigid-X™ Silent X-Stream™ Quiet Panel Coolers

Silent X-Stream™ NEMA 12 (IP56) Quiet Panel Coolers

Silent X-Stream™ NEMA 12 (IP56) Quiet Panel Coolers for standard cabinet enclosures and panels. All units 303/304 stainless steel for corrosive environments and long life. Super quiet to about 64 dBA. Utilizing a hot and cold end muffling kit the unit is made extra quite to under 64 dBA depending on capacity. The hot end muffler also acts a “heat guard” - you can actually wrap your hand around it without feeling much heat.

<< Learn More >>

Silent X-Stream™ NEMA 3R (IP14) Quiet Panel Coolers

Silent X-Stream™ NEMA 3R (IP14) Quiet Panel Coolers for cabinet enclosures and panels in outdoor use. All units 303/304 stainless steel for corrosive environments and long life. Super quiet to about 64 dBA. Utilizing a hot and cold end muffling kit the unit is made extra quite to under 64 dBA depending on capacity. The hot end muffler also acts a “heat guard” - you can actually wrap your hand around it without feeling much heat.

<< Learn More >>

Silent X-Stream™ NEMA 4-4x (IP66) Quiet Panel Coolers

Silent X-Stream™ NEMA 4-4x (IP66) Quiet Panel Coolers for cabinet enclosures and panels in wash down applications. All units 303/304 stainless steel for corrosive environments and long life. Super quiet to about 64 dBA. Utilizing a hot and cold end muffling kit the unit is made extra quite to under 64 dBA depending on capacity. The hot end muffler also acts a “heat guard” - you can actually wrap your hand around it without feeling much heat.

<< Learn More >>

  Small Enclosure Box Coolers

Small Enclosure Box Coolers

The Frigid-X™ Small Enclosure Cooler or Box Cooler is used for cooling small enclosures for laboratory use, environmental chambers and any application where an enclosure needs cooling (Note: Not approved for electrical and electronic control panels but may be used if approvals not required).

<< Learn More >>

Accessories for Cabinet Enclosure Coolers

Muffling Kits for Cabinet Enclosure Coolers

In many environments where the surroundings are very quiet or if personnel are working next to control panels, the Hot End and Cold End Muffing kits can reduce the noise levels an additional 8 dBA depending on air capacity used!!!

<< Learn More >>

Nex Flow, Cabinet Panel Coolers

Cabinet Cooling Accessories

Cabinet Cooling Accessories - Filtration, Hose Distribution Kit, Sealing & Mounting

<< Learn More >>

Nex Flow, Cabinet Panel Coolers

Electronic Thermostat

Electronic Thermostat ELC (Electronic Control Digital Thermostat) is a way for precise control of one or two Nex Flow™ Frigid-X™ cabinet panel coolers.

<< Learn More >>

Nex Flow, Cabinet Panel Coolers

Side Mounts For Tight Spaces

Cabinet Cooling Solutions With Frigid-X™ Cabinet Enclosure (Panel) Coolers are normally mounted on the top of the enclosure but if space does not permit, you can use our Side Mount Kit.

<< Learn More >>

By-Pass System for Panel Coolers

In very dirty environments, it can be advantageous to have a small amount of compressed air entering the control panel when the panel cooler is not operating (turned off utilizing a solenoid and thermostat package to conserve energy).

<< Learn More >>

 

About Tech Sales Co.

Tech Sales Co., was established in 1983 with headquarters near Toronto, Canada, Tech Sales Co., maintains a network of branch offices and associated representatives and distributors across Canada. Our technical support in-house is strong with backup from principles around the world. Expertise is available in the following specific areas: compressed air blow off, static control, surface treatment of plastics, plastic flaw repair, non-hazardous chemicals, ultrasonic cleanings systems and other special technologies

Sitemap

Our Products

Tech Sales Co., is a manufacturers representative company devoted to unique technologies for industry. We represent Nex Flow™ Air Products Corp., HAUG North America, Dynamic Descaler and have other products for static control and elimination, corona treatment, plastic repair and environmentally friendly chemicals.

Sample Content

Tech Sales Co., provides an indepth information on Air Amplifiers, showing Nex-Flow™ Standard Air Amplifiers, Adjustable Air Amplifiers and Adjustable Gauged Air Amplifiers. Air Knives feature Standard Air-Blade™ Air Knives, Stainless Steel Air-Blade™ Air Knife, X-Stream™ Air-Blade™ Air Knife and our X-Stream™ Hard Anodized Air-Blade™ Air Knife. HAUG North America products feature Staic Elimination Products. Dynamic Descaler a revolutionary biodegradable descaler and much more information on is available on this web site.

Get in Touch

  • Telephone:
    (416) 410-1313
  • Email:
    lesr@tech-sales.com
  • Address:
    10520 Yonge Street, Unit 35B-220
    Richmond Hill, ON
            L4C 3C7