Infrared Thermometers Linear C-1000 Series

Advanced User Interface & Easy To Use

The Linear C-1000 Series Infrared Thermometers are self-contained, battery-operated devices for non-contact temperature measurement. Each unit consists of a probe and a display unit. The probe unit easily attaches to the display unit for single hand operation. The power source is a single 9-Volt alkaline battery. The C-1000P is supplied with an external power jack and an analog output jack which are located on the side of the display unit.

p_C-1000_series.jpg (13343 bytes)

The Linear C-1000 Series Infrared Thermometers utilize a passive sensor which receives and measures infrared radiation from an object. Since temperature is measured without contact, heat is not removed from the measured object. Therefore accuracy of the reading is assured. Measurements are more rapidly (less than one second) so that thermal patterns and transient phenomena can be observed. Moving objects, dangerous materials, process steps, and operating electrical components can be safely and effectively measured. The C-1000 is ideal for taking and storing readings during Preventive Maintenance checks on several pieces of equipment.

Features

	-70° (56°C) to 1000°F (538°C) measurement range
	Adjustable emissivity from .10 to 1.0 in .01 steps
	Attach probe for single hand operation or detach probe for hard to reach measurements
	Displays minimum/maximum, delta or average readings
	Analog output optional
	Powered by internal 9-volt battery or 110 VAC (optional)

The Linear C-1000 Series Infrared Thermometers uses a Liquid Crystal Display to enter commands and display data. This innovation greatly simplifies the operation of the product. A two position switch located on the left side of the display unit is used to select POWER ON and OFF. A new technology liquid crystal display runs the full length of the front of the display unit. This technology allows the user to easily identify the system mode as the mode switch changes colors when selected. With the exception of turning on the power, all functions are controlled by touching the appropriate position on the display.

The C-1000 System contains nonvolatile memory. The nonvolatile memory feature allows the system to remember previous settings upon power up. Measurements can be made from a distance as close as ¼ inch (0.6 cm). As the distance to the source is increased, the diameter of the measured area increases proportionally. For the C-1000 at 3 inches (7.6 cm) the measured area is about 1 inch (2.5 cm) in diameter. The analog output signal is 1 millivolt per degree. This signal is often useful in further troubleshooting process related problems.

Typical Applications

Non-Destructive Testing

	Motors and Bearings
	Circuit Boards
	Jet Engines
	Friction Testing

Textiles

	Dyeing
	Drying
	Heat Setting
	Curing

Electronics

	Wave Soldering
	Circuit Board Testing
	Potting and Casting

Pharmaceuticals

	Tablet Drying
	Affixing Labels
	Packaging Sealing

Floor Covering

	Laminating
	Drying
	Calendering
	Printing

Energy Auditing

	Stream Trap Inspection
	Thermal Insulation
	Integrity
	Power Distributing
	Panels
	Stream Lines
	Heat Exchanges

Rubber

	Extrusion
	Mold Control

Food Processing

	Baking
	Pasteurizing
	Mixing

Paper

	Web Monitoring
	Calendering
	Coating, Laminating
	Printing
	Lime Kiln Control
	Shell Hot Spots
	Plugged Syphons

Plastics

	Extrusion
	Injection Molding
	Vacuum Forming
	Laminating
	Calendering
	Foam Sheet Extrusion

Maintenance

	Hot Bearings
	Engine Performance
	Boiler Hot Spots
	Energy Auditing
	Power Distribution Systems
	Electrical Buss Bars

Accessories

C-WAND - Used to maintain a constant distance between the probe and the target.
C-STAND -Mounts the handheld probe for stationary applications requiring continous measurement.
C-CASE - Vinyl carrying case with belt loop.
C-ADP - 110 VAC power adapter. (Supplied with "P" version)
C-ANA - Analog output cable. (Supplied with "P" version)