|
1.
Bonding
wire
2. Ground wire
3. Conductive hose,
(106 Ohms)
4. Conductive fitting of
hose into hose
connector
5. Metal pump tube for
zone "0" in Stainless
Steel or Hastelloy C
6.
Explosion
proof motor
Lutz Silver Star or
MD-1/MD-2 (Ex)
Air-Motor
7.
Nozzle
Stainless Steel
or
Brass
8.
Flow
control system
(Ex)
9.
Emission
proof fume
barrier
|
 |
Bonding
is the electrical interconnection between containers (such as
a drum and a recieving can). Bonding must be completed before
pumping begins. For better conductivity paint and dirt shall be
removed from the contact points.
Grounding is the electrical connection
between a container and a "constant ground". A "constant
ground" would be a metal pipe (water pipe) or rod in contact
with the earth. An underground tank and piping connected to it
would be inherently grounded by nature of the installation.
Both Bonding and Grounding
of containers of flammable liquids are required under U.S. government
OSHA regulations and National Fire Protection Assocaition Code
77, static electricity
Metal pumps in stainless steel or Hastelloy C and pump
motor must be bonded to metal container or grounded, if used with
plastic container. Normal safety procedures must be used at all
times when operating any piece of machinery.
|
|
Specification |
Order
No. |
 |
  Ground
and Bonding Wire
Serves to create electrically conductive connection between
explosion proof pump and container as earthing and equipotential
bonding function. |
Ground
Wire 6'
Bonding Wire 10' |
0204-994
0204-995 |
 |
 Electrically
Conductive Hoses
Caution: Electrical conductivity is assured through the use
of break resistant textile copper threads in the rubber coating.
If correctly installed, resistance during the entire life
of these will remain below 106 ohms. |
|
Contact
Factory
for details |
 |
 Stainless
Steel Nozzle
Ideally suitable for filling and transferring liquids in food
and pharmeceutical industries. Stainless steel 316 housing
and valve tappet FPM (Vitron®) seals. Additional costs for
EPDM or Vitron®/FEP seals. Other seals on request Avaliable
with male thread 1". |
| Operating pressure: |
max. 43.5 psi |
|
| Viscosity: |
max. 760 cps |
|
| Rate of flow: |
max. 13.2 GPM (water) |
|
| Temperature of
medium: |
max. 176 ºF |
|
| Weight: |
approx. 2.2 lbs |
|
| Connection: |
hose barb 3/4" |
0204-689 |
|
hose barb 1" |
0204-699 |
|
hose barb 1 1/4" |
0204-700 |
|
male thread 1" |
0204-730 |
|
 |
Brass
Nozzle With Turning Knuckle
Brass housing and valve tappet. PTFE seals. For filling and
transferring solvents and neutral liquids. |
| Operating pressure: |
max. 58 psi |
|
| Viscosity: |
max. 760 cps |
|
| Rate of flow: |
max. 21.1 GPM (water) |
|
| Temperature of
medium: |
max. 176 ºF |
|
| Weight: |
approx. 1.32 lbs |
|
| Connection: |
female thread 1" |
0372-498 |
|
 |
 Modular
Electrical Flow Control System
For metering all kinds of liquids.
Wide range of applications: Directly at the drum pump, remote
or in-line operation possible. Convenient pre-setting of required
volume using a numerical keypad. A comprehensive range of
system components offers practical problem solutions. Two
standard and three explosion proof meter versions are available.
|
|
 |
 Emission
Proof Fume Barrier
To prevent emission of dangerous gasses when using a drum
pump, thus protecting the operator, the environment, and the
drive moter from hazardous, aggerssive gasses and vapors.
Two venting valves ensure pressure compensation inside and
outside the drum.
Connection for gas displacement pipe: 3/8" female Seals:
Vitron® as standard. Other threads and seal materials on request. |
Material:
brass
stainless steel |
Pump tube diameter:
1.62 inches
1.62 inches |
0204-252
0204-253 |
|
 |
Reducer
To connect quick connect/disconnect hose coupling with pump
tube.
femal thread 1-1/4" and 1" |
Material:
Stainless steel |
0372-019 |
 |
Quick-Action
Hose Coupling
Male Adapter |
in
stainless steel, male 1" |
0372-024 |
 |
Female
Hose Couplings
Ensure rapid, leakproof connection between pump and hose.
Avaliable in stainless steel and polypropylene. |
in
stainless steel,
female 1",
seal FEP/EDPM |
0372-025 |
|
Emission
Proof Fume Barrier
To prevent emission of dangerous gasses when using a drum
pump, thus protecting the operator, the environment, and the
drive moter from hazardous, aggerssive gasses and vapors.
Two venting valves ensure pressure compensation inside and
outside the drum. Connection for gas displacement pipe: 3/8"
female Seals: Vitron® as standard. Other threads and seal
materials on request. |
|
Material:
|
Pump
tube diameter:
|
|
|
brass
|
1.62
inches
|
0204-252
|
|
stainless
steel
|
1.62
inches
|
0204-253
|
|
 |
Foot Strainers
Available in PP, brass, and stainless steel, for mounting
on the pump foot. Prevents impurities from entering the pump. |
|
Material:
|
pump
tube:
|
|
|
brass
|
Alu
dia. 41 mm, SS dia 41 mm
|
0204-633
|
|
stainless
steel
|
HC
dia 38 mm
|
0204-632
|
|
stainless
steel
|
SS
dia. 41 mm
|
0204-617
|
|
stainless
steel
|
B70V
|
0204-802
|
|
 |
Discharge
Spouts
For transfer liquids to other vessels. Available in PP, aluminum,
and stainless steel. Spouts are connected onto the pump's
discharge. |
|
Material:
|
nominal
diameter:
|
wing
nut:
|
|
|
SS
|
1"
|
1-1/4"
|
0204-225
|
|
SS
|
1-1/2"
(for B70V)
|
1-1/4"
|
0204-226
|
|
|
