|
|
 |
Filter
Ventilator Systems from Electra Kool
|
 Filter
Ventilator System
Model 1000A
For enclosures up to 500 Cubic ft.
Filter Ventilator System Model 1000A is available
with 1 or 3 phase drive motors. a 6" (nominal) square mounting
flange is fitted on the outlet. Inlet/outlet are provided with finger
guards for safety. The Filter Blower Unit Model 1000A produces 1200
CFM.
The main pleated paper filter has a huge 94 sq. ft. area and a 1/2"
thick polyester pre-filter. A single wingnut eases removal &
replacement.
The complete system includes four louvered vents, a digital thermometer
with 10 ft. lead, an air deflector, mounting fasteners, and operation
installation instructions.
Order single phase units as Assembly #10290
Order three phase units as Assembly #10292
|
 Filter
Ventilator System
Model 500C
For enclosures up to 200 Cubic ft.
Filter Ventilator System Model 500C is avaialble
with 1 or 3 phase drive motors. A 4" (nominal) square mounting
flange is fitted on the outlet. Inlet/Outlet are provided with
finger guards for safety. The Filter Blower Unit Model 500C produces
455 CFM.
The main pleated paper filter has a huge 44
sq. ft. area and a 1/2" thick polyester pre-filter. A single
wingnut eases removal & replacement.
The complete system includes three louvered vents, a digital thermometer
with 10 ft. lead, an air deflector, mounting fasteners, and operation
installation instructions.
Order single phase units as Assembly #10190
Order three phase units as Assembly #10192
|
 Filter
Ventilator System
Model 150C
For enclosures up to 25 Cubic ft.
Filter Ventilator System Model 150C is unique
in that the motor is built into the impeller! The die-cast aluminum
housing has a regtangular outlet about 2" x 3". The inlet
and outlet have finger guards installed. It is a single phase 115
volt motor (3 phase not available).
The main filter contains approximately 5.6 square feet of pleated
paper and is fitted with a prefilter blanket. Filters are easily
removed with on wing nut and may be cleaned for reuse!
The Filter Ventilator System Model 150C system includes a louvered
vent for hot air exit, a deflector plate to direct cooler air towards
the "hot spots", and external capacitor, mounting fasteners
and a digital thermometer to monitor internal temperature.
Order as Assembly #10010
|
 Filter
Ventilator System Model 60A
For enclosures up to 10 Cubic ft.
Filter Ventilator System Model 60A is our
smallest Filter Ventilator System and is suggested for use on small
enclosures up to 10 cubic feet, particularly in the metal working
industry where oil mist causes problems! It produces 60 CFM and
uses a 115 volt blower motor (3 phase is not available).
The main filter has about 2-1/4 square feet of pleated paper filter
area with a 1/2" thick prefilter for extended life.
The filter Ventilator System Model 60A includes the filter/blower,
a louvered vent for hot air exit, mounting fasteners and installation/operation
instructions.
Order as Assembly #10060
|
 Filter
Ventilator System Model 1400
For enclosures up to 600 Cubic ft.
Filter Ventilator System Model 1400 produces
1400 CFM and has an 8" oultet. The standard unit is equipped
with a 3 phase drive motor. the mounting flange is cast integral
with the blower casing and both inlet and outlet have finger guards
for safety.
The pleated paper filter has 45 sq. ft. of area and life is further
extended with the 1/2" polyester prefilter wrap. A single wingnut
makes removal easy!
The 1400A is equipped with louvered vents, an air deflector, a digital
thermometer, mounting fasteners, and installation/operation instructions.
It is a complete package with nothing else to buy!
Order as Assembly #10831
|
|
Products