Multitherm® Heat Transfer Fluids Products
|
|
Heat
Transfer Fluids: High Temperature Applications
MultiTherm
PG-1®
|
|
- Operating range from 10°F (-12°C)
to 600°F (315°C)
- Food grade (NSF registered, FDA certified
Non-Toxic, USDA Chemicallyacceptable, Kosher
certified)
- Low viscosity / Low pour point
- Non-Toxic, Non-Hazardous, Non-Fouling
- Designed for applications in Food, Chemical,
Plastics, and Die-Casting
- Thermal expansion coefficient 0.00035/ºF
(0.00063/ºC)
- For use in closed loop, liquid phase heating
and cooling systems to 600°F
|
MultiTherm OG-1®
|
|
- MultiTherm's oxidation grade fluid for
open or closed loop systems
- Operating range from 10°F (-12°C)
to 550°F (290°C)
- Highly refined to have High flash point
- Oxidation resistant - Very Low vapor pressure
- Non-Toxic, Non-Hazardous
- Designed for applications where the hot
heat transfer fluid comes in contact with
atmosphere
- Thermal expansion coefficient 0.00056/ºF
(0.00102/ºC)
|
MultiTherm
503®
|
|
- When you have heating and cooling in the
same loop
- Operation range: from 50°F (-10°C)
to 500°F (260°C)
- Meets FDA specifications but not certified
- Very low viscosity - Very low pour point
- Low vapor pressure
- Relatively high flash point - Non-Toxic,
Non-Hazardous
- Designed for applications in Plastics,
Chemical, and other processing industries
- Thermal expansion coefficient 0.00051/ºF
(0.00092/ºC)
- For use in closed loop, liquid phase heating
and cooling systems from 10°F to 500°F
|
MultiTherm IG-4®
|
|
- Operating range from 10°F (-12°C)
to 600°F (315°C)
- Highly refined to have High flash point
- Oxidation resistance - Very Low vapor
pressure
- Non-Toxic, Non-Hazardous
- Designed for applications in Asphalt,
Chemical, Plastics, Laundries and Die-Casting
- Thermal expansion coefficient 0.00054/ºF
(0.00097/ºC)
- For use in closed loop, liquid phase heating
systems up to 600°F
- MultiTherm IG-4 is an upgrade of, and
a direct replacement for MultiTherm IG-2®
|
MultiTherm IG-1®
|
|
- Operating range from 10°F (-12°C)
to 550°F (288°C)
- Economical heat transfer fluid
- High flash point
- Non-Toxic, Non-Hazardous
- Designed for applications in Asphalt,
Roofing, Paper, Particle Board and Die-Casting
- Thermal expansion coefficient 0.00054/ºF
(0.00098/ºC)
|
|
|
Heat
Transfer Fluids: Low Temperature Applications
MultiTherm
ULT-170®
|
|
- For ultra low temperature applications
- Operation range down to -170°F (-112°C)
- Low freezing point - Low viscosity at
ultra-low temperatures
- Thermally stable & biodegradable
- Single fluid usage for sterilization applications
- Designed for Pharmaceutical, Chemical,
Freeze-Drying, and Cryogenic applications
- Extends low-end operating ranges far beyond
the boundaries of most competitive brands
- Remains pumpable even at temperatures
below -170°F (-112°C)
|
MultiTherm
WB®
|
|
- Aqueous-based for Low temperature applications
- Operation range down to -58°F (-50°C)
- Non-toxic, None-flammable
- Designed for Ice Rink, Food, Refrigeration,
Breweries/Distilleries, and HVAC applications
- Engineered to deliver the desirable low-end
temperature performance of synthetic organic
and silicone-based fluids
|
|
|
Heat
Transfer Flushing/Cleaning Fluid
MultiTherm
FF-1®
|
|
- Specially formulated flushing fluid to
clean out systems during:
- Start-ups - to remove loose material
such as weld splatter, fines, particulate
matter, etc. left in lines and equipment,
along with oil and some preservative
coatings
- General Maintenance - for removing
particulate matter and used heat transfer
fluid from a system prior to recharge
or changeover from one fluid to another.
- Compatible with all MultiTherm and mineral
oil heat transfer fluids.
- Thermal expansion coefficient 0.00047/ºF
(0.00085/ºC)
|
MultiTherm
PSC Plus®
|
|
- Specially
formulated flushing fluid to clean out systems
during:
- Start-ups - to remove loose material
such as weld splatter, fines, particulate
matter, etc. left in lines and equipment,
along with oil and some preservative
coatings
- General Maintenance - for removing
particulate matter and used heat transfer
fluid from a system prior to recharge
or changeover from one fluid to another.
- Compatible with all MultiTherm and mineral
oil heat transfer fluids.
- Thermal expansion coefficient 0.00047/ºF
(0.00085/ºC)
|
|
|
Heat
Transfer Filtration
Hot
Oil Filtration Systems
|
|
Hot
oils degrade by thermal cracking and oxidation.
The two by-products of oil degradation is sludge
and coke due to carbon build-up. These products
can collect through-out your system but specifically
in pump seals and internals, valves, etc. that
result in equipment problems and possibly eventual
system breakdown. |
|
|
Replacement or
New
|
|
Chilled Water, Hot Water, Steam, DX or Condenser
Heavy duty industrial coils of all types
- Duplicate existing dimensions and performance
- Special 5 work day and 10 work day quick
shipments available
- Hot water duct booster coils in stock
- Call 800-225-7440 for immediate pricing,
technical information and delivery information
|
|
|
T-Bar
Self Contained AC Units
T-Bar Self Contained
AC Units
|
|
A T-Bar Unit
from Multitherm®
is the answer to your special cooling and dehumidification
needs. And, it fits right into a standard 2'
x 4' suspended ceiling panel, with no floor
space needed.
|
|
|
JUNIORFLUX
Pump & Motor Unit/PP From MultiTherm
|
|
For filling,
emptying, transferring or dispensing small amounts
of liquid out of carboys, hobbocks, canisters,
narrow-necked containers or barrels FLUX now
offers a better performance: the new JUNIORFLUX
pumps type F 310 and F 314.
The JUNIORFLUX pumps are available in polypropylene
(PP), polyvinylidene fluoride (PVDF) or stainless
steel (S), both in version with mechanical seal
Type F 310 or sealless Type F 314.
A powerful 230 Watt commutator motor with a
2-speed switch allows sensitive, fast and therefore
low-cost and safe filling operations. The motor
is built to protection class II, splash-proof
and comprises an overload cut-out switch. Another
feature is the modern and ergonomically structured
design for single-hand operation. |
|
|
|
