|
Product
Information
|
3300C -
Slade’s Cost Effective Pump and Valve Packing
|
|
Reinforcement:
|
Each yarn of graphite foil is reinforced with
high strength structural carbon fiber
|
|
Temp:
|
Non-oxidizers: -400°F/-240°C to
5400°F/3000°C
Mild Oxidizers to 1800°F/1000°C
|
|
Pressures:
|
Valves to 1000 PSI/70 BAR (for higher pressures,
consult factory)
|
|
pH Range:
|
1-14
|
|
3300W:
|
Inconel wire reinforced for higher pressures:
5000 PSI/350 BAR
|
|
3300LC:
|
Low chloride, high purity for nuclear service
|
|
3300LS:
|
Low sulfur, high purity for nuclear service
|
|
3300G
- Slade’s Best All Purpose Pump and Valve
Packing
|
|
Reinforcement:
|
Corners and yarns of graphite foil reinforced
with high strength structural carbon fiber
|
|
Temp:
|
Non-oxidizers: -400°F/-240°C to
5400°F/3000°C
Mild Oxidizers to 1800°F/1000°C
|
|
Pressures:
|
Valves to 5000 PSI/70 BAR without end-rings
|
|
Pumps:
|
Flush-free in many services to 4800 FPM (1400
m/min)
|
|
|
1-14
|
|
Applications:
|
Chemicals, steam, hydrocarbons, etc.
|
|
Advantages:
|
-
One packing inventory for all pumps and valves
-
Works well on worn sleeves
-
Difficult to overtighten
-
No added lubricants to squeeze out or burn
off
-
Eliminates flush-water in most applications
-
Not necessary to replace entire set, just
add ring
-
Won’t glaze or harden
-
Eliminates most leaks
-
Amperage reduction of 15% is typical
-
No special end-rings required
-
Outlasts typical packings by factor of 6
-
4800 fpm/24 ms (without flush water)
-
pH 1-14
-
Operates virtually leak-free in most applications
-
Low chloride/sulfur available for nuclear
service
|
|
Installation:
|
-
Check clearances and dimensions
-
Best to use no more than 5 rings in stuffing
box (us Slade spacer bushings to reduce
rings
-
Cut rings on the bias (45° angle), stagger
joints
-
Compress each ring 25% (especially the first
ring)
-
Loosen gland to allow it to relax
-
Snug the gland bolts and start the pump
|
|
3300GLC:
|
Low chloride for nuclear service
|
|
3300GLS:
|
Low sulfur for nuclear service
|
|
3300K
- Slade’s Best Triplex Pump, Reciprocating
Packing
|
|
Reinforcement:
|
Same as 3300C, but with added Kevlar fiber corners
|
|
Temp:
|
Maximum temperature of 500°F/260°C
|
|
Applications:
|
Reciprocating/plunger, wastewater, steam and
ammonia pumps
|
|
Pressures:
|
5000 PSI/350 BAR
|
|
pH Range:
|
2-12
|
|
3300CJ
- Slade’s Anti-Extrusion Carbon Fiber Packing
|
|
description:
|
Carbon jacketed 3300C
|
|
Pressures:
|
Valves to 1000 PSI/70 BAR (for higher pressures,
consult factory)
|
|
Application:
|
Used as anti-extrusion end-ring
|
| 3300CJK
- Slade’s Anti-Extrusion Carbon Fiber Packing |
|
description:
|
3300C with Kevlar corners
|
|
Temp:
|
500°F/260°C
|
|
Application:
|
Used as end-ring to provide anti-extrusion (especially
with large throat clearances) and to provide barrier
to particulate contamination
|
.gif)
Replaces expensive Mechanical
Seals at 25% of the cost. Split to install without dismantling
the pump
An alternative to machining
costly bushings is to utilize Slade’s DSS Sealing System.
No machining, no dismantling of the pump. Achieve leak-free,
flush-free service. It comes fully unitized, ready to
install, and we'll inform you of the gland compression required.
If you follow Slade’s installation instructions, you eliminate
fear of over-tightening.
The SLADE DSS sealing system
can achieve Mechanical Seal performance at packing costs. Contact
Slade for more information on the DSS bushing.
Pyro-Tex
Joint Sealant
Slade’s self-forming
gasket, the Pyro-Tex Joint Sealant, is made from patented graphite-foil
encapsulated carbon-fiber reinforcement yarns. This self-forming
gasket when in place is compressed to fit snugly. The Pyro-Tex Joint
Sealant HP (high pressure) is made from the same patented
graphite-foil encapsulated stainless-steel foil reinforcement
yarns as our sheet. Available in 25 and 50 foot spools in various
configurations, shapes, and thicknesses.
-
Change gasket without pulling tube bundles
-
Adhesive bonds in place during installation
-
Self forms into endless gasket
-
Made to virtually any thickness or width
-
Never hardens or dries out
-
Metallic reinforcement impedes extrusion
-
Readjustable, often re-usable
-
Individual strands reinforced with carbon
fiber, 304 SS, or Inconel foil
-
Packaged on plastic spools
-
Inventory just one or two sizes
-
.gif) Eliminates
the need to remove heat exchanger tubes from the shell
-
Performs better than:
-
More reliable than TFE joint sealants
-
Eliminates large inventories
-
Easier to Handle
-
Stops damage from rough handling
-
Doesn't kink out of shape
-
Adjusts to warped flanges
-
Fills pits and scratches up to 1/8"
deep
Pressures
Temperatures
-
Stainless Steel version: 1400°F
-
Inconel Steel version: 1800°F
-
Carbon fiber version: 1800°F
Chemical
compatibility:
|
