Hydra-Cell Sealless Pumps
Hydra-Cell Sealless Pumps from Wanner Engineering
Hydra-Cell Sealless Pumps. Positive Displacement Pumps with a sealless pumping chamber so there are no seals, packing or cups to leak or replace. The sealless design and check valves enable Hydra-Cell to handle abrasives and particulates that would damage other types of pumps.
In addition, Hydra-Cell Sealles Pumps can run dry indefinitely without damage to the pump.
The multiple-diaphragm design of Hydra-Cell provides virtually pulse-less, linear flow without the need for expensive pulsation dampeners.
| Max Flow: 8.8 gpmMax Pressure:1500 psi (103 bar) Metallic Pump Heads350 psi (24 bar) Non-Metallic Pump Heads |
Max Flow: 36.5 gpmMax Pressure:1500 psi (103 bar) Metallic Pump Heads |
Max Flow: 20 gpmMax Pressure:1000 psi (69 bar) Metallic Pump Heads350 psi (24 bar) Non-Metallic Pump Heads |
Max Flow: 3.1 gpmMax Pressure:1200 psi (83 bar) Metallic Pump Heads350 psi (24 bar) Non-Metallic Pump Heads |
 |
The graph above displays the maximum flow capacity at a given pressure for each model series. The table below lists the maximum flow capacity and maximum pressure capability of each model series.
Please Note: Some models do not achieve maximum flow at maximum pressure. Refer to the individual model specifications in this section for precise flow and pressure capabilities by specific pump configuration.
* 350 psi (24 bar) maximum with PVDF liquid end; 250 psi (17 bar) maximum with Polypropylene liquid end.
** Consult factory for correct component selection for temperatures from 160 ̊F (71 ̊C) to 250 ̊F (121 ̊C).
| Max Flow: 96 gpmMax Pressure:2100 psi (145 bar) Metallic Pump Heads |
Max Flow: 45 gpmMax Pressure:3500 psi (241 bar) Metallic Pump Heads |
Max Flow: 26 gpmMax Pressure:5000 psi (345 bar) Metallic Pump Heads |
|
T100 Pump Series |
T100 Pump Series |
T100 Pump Series |
 |
The graph above displays the maximum flow capacity at a given pressure for each model series. The table below lists the maximum flow capacity and maximum pressure capability of each model series.
Please Note: Some models do not achieve maximum flow at maximum pressure. Refer to the individual model specifications in this section for precise flow and pressure capabilities by specific pump configuration.
| Model | Maximum Capacity | Maximum Discharge Pressure | Maximum Inlet Pressure | Maximum Operating Temperature | ||||
| (gpm) | (l/min) | (psi) | (bar) | (psi) | (bar) | (F)* | (C)* | |
| T100E | 96.0 | 366.1 | 1500 | 103 | 500 | 34 | 180 ̊ | 82 ̊ |
| T100F | 76.5 | 289.6 | 1850 | 128 | 500 | 34 | 180 ̊ | 82 ̊ |
| T100H | 68.0 | 257.8 | 2100 | 145 | 500 | 34 | 180 ̊ | 82 ̊ |
| T100K | 45.0 | 170.4 | 3000 | 207 | 500 | 34 | 180 ̊ | 82 ̊ |
| T100M | 38.0 | 143.8 | 3500 | 241 | 500 | 34 | 180 ̊ | 82 ̊ |
| T100S | 26.0 | 98.4 | 5000 | 345 | 500 | 34 | 180 ̊ | 82 ̊ |
* Consult factory for correct component selection for temperatures above 180 ̊F (82 ̊C) or below 40 ̊F (4 ̊C)
| Max Flow: 195 gpmMax Pressure:2100 psi (145 bar) |
Max Flow: 78 gpmMax Pressure:3500 psi (241 bar) |
|
Q155 Pump Series |
Q155 Pump Series |
 |
 |
The graph above displays the maximum flow capacity at a given pressure for each model series. The table below lists the maximum flow capacity and maximum pressure capability of each model series.
Please Note: Some models do not achieve maximum flow at maximum pressure. Refer to the individual model specifications in this section for precise flow and pressure capabilities by specific pump configuration.
Economical
Real Savings from using Hydra-Cell Sealless pumps
- Can save approximately 30% to 50% on initial costs because Hydra-Cell Sealless Pumps use lower horsepower motors to achieve the same flow rates and pressures as other pumps.
- Compact design with smaller footprint provides more efficient use of floor space.
- Operates at 85-90% energy efficiency to reduce operating costs.
- Seal-less design reduces maintenance and repair expenditures and minimizes the cost of spare parts compared to other types of pumps.
Capable
Hydra-Cell Sealless pumps can deal with abrasive liquids
- Tolerates abrasive solids and particulate matter up to 800 microns (depending on pump model) and 9 hardness (Mohs) without the need for fine filtration.
- Multiple diaphragms provide virtually pulse-less flow that exceeds API 675 standards for accuracy, linearity, and repeatability.
- Low-shear pumping action ensures integrity of long-chain structures.
Environmental
Hydra-Cell Sealless pumps are environmentally friendly
- Liquids are 100% sealed from the atmosphere.
- No leak path for toxic vapors or harmful gasses.
- No seals to leak any Volatile Organic Compounds (VOC).
- Lower energy costs to operate pump.
Versatile
Versatility of Hydra-Cell Sealless pumps is unmatched
- Variety of styles and models to pump a wide range of flow capacities and pressure ratings.
- Hydraulically-balanced diaphragms can pump low-to-high- viscosity liquids throughout the entire pressure range of the pump.
- Available in a variety of construction materials to meet a wide range of applications and ensure optimum pumping life even when handling aggressive fluids.
- Can be fitted with SAE, ANSI or DIN flanges as well as IEC or NEMA motor mounts.
- Can be provided with ATEX certification or other certification to adapt to specific applications or meet international standards.
- Design allows for easy interchangeability of pump head materials and can accommodate mixing different materials with one pump head.
Reliable
Hydra-Cell Sealless pumps are most reliable
- Can run dry without damage to the pump.
- Robust design tolerates non-ideal operating conditions.
- No seals, packing or cups to leak or replace.
- Typically runs up to 6,000 hours between lubricating oil changes.
- Can pump acids, slurries and liquids containing up to 40% of non-dissolved solids.
- Does not rely on the fluid being pumped for lubrication.
- No tight tolerances susceptible to corrosion or solid particles.
