 Monarch Pumps offers a wide range of Sump Pumps and Sewage Pumps. This section features the UP16M SERIES Submersible Utility Pump, SP25A SERIES Submersible Sump Pump, SP33 SERIES Submersible Sump Pump, ESP33 SERIES Submersible Sump Pump, ESP50 SERIES Submersible Effluent Pump, BE SERIES Self Priming Effluent Pump, WS SERIES Submersible Effluent Pumps, WSV SERIES Submersible Sewage Pumps Vortex, WS SERIES Submersible Grinder Pump aanf the EPE SERIES Centrifugal Pumps.
|
|
UP16M SERIES Submersible Utility Pump
SOLIDS HANDLING CAPABILITY - 1/8”
MOTOR - 1/6 HP, 115 volt, thermal overload protected. 2.1 full load amps. 10 foot power cord. Stainless steel heat treated shaft. Continuous duty "oil free" motor. Permanently lubricated lip seal. CSA approved.
PUMP CASING - Corrosion resistant aluminum for superior heat dissipation. ¾" NPT discharge.
IMPELLER - Constructed of durable glass reinforced thermoplastic.
GARDEN HOSE ADAPTER - For convenient hook up.
BOTTOM SUCTION DESIGN - Bottom suction design allows pumping to within ¼" of the surface. Built-in suction strainer to eliminate internal damage from possible debris. Removable filter screen for easy cleaning.
Specifications
|
|
|
SP25A SERIES Submersible Sump Pump
SOLIDS HANDLING CAPABILITY - 1/8” MOTOR - ¼ HP, 115 volt, thermal overload protected. 3.2 full load amps. 10 foot power cord. Stainless steel heat treated shaft. Continuous duty "oil free" motor. Permanently lubricated lip seal. CSA approved.
PUMP CASING - Corrosion resistant aluminum for superior heat dissipation. 1¼" NPT discharge.
IMPELLER - Constructed of durable glass reinforced thermoplastic.
SWITCH - Automatic, mercury free, mechanical float switch.
BOTTOM SUCTION DESIGN - Bottom suction design allows pumping to within ¼" of the surface. Built-in suction strainer to eliminate internal damage from possible debris. Removable filter screen for easy cleaning.
Specifications
|
|
|
SP33 SERIES Submersible Sump Pump
SOLIDS HANDLING CAPABILITY - ¼”
MOTOR - 1/3 HP, 115 volt, thermal overload protected, CSA approved. 3.5 full load amps. Continuous duty "oil free" motor. Stainless steel motor housing improves heat dissipation for longer motor life. Complete with a 10 foot power cord. Stainless steel heat treated shaft. Permanently lubricated lip seal.
PUMP CASING - Fully constructed of durable reinforced thermoplastic for excellent corrosion resistance. 1¼" NPT discharge for ease of installation.
IMPELLER - Non clogging design constructed of durable reinforced thermoplastic.
SWITCH - Automatic, mercury free, mechanical float switch. Also available in manual operation.
BOTTOM SUCTION DESIGN - Built-in suction strainer to eliminate internal damage from possible debris. Removable filter screen for easy cleaning.
Specifications
|
|
|
ESP33 SERIES Submersible Sump Pump
SOLIDS HANDLING CAPABILITY - ½”
CONSTRUCTION - Rugged cast iron motor housing dissipates heat away from motor. Rugged corrosion resistant, molded polypropylene pump body.
MOTOR - 115 volt thermal overload protected, CSA approved continuous duty “oil free” motor. Stainless steel heat treated shaft, upper and lower permanently lubricated ball bearings, permanently lubricated double lip seal. 5.6 full load amps.
IMPELLER - 5 vane reinforced polypropylene, handles ½" spherical solids - with brass insert.
SWITCH - Automatic with piggy-back mercury free mechanical float switch or vertical float switch. Also available in manual operation.
POWER CORD - 10 ft. power cord on manual and vertical float switch models, 20ft with integral float switch.
DISCHARGE - 1½" NPT. Reducer bushing for 1¼" discharge included.
Specifications
|
|
|
ESP50 SERIES Submersible Effluent Pump
SOLIDS HANDLING CAPABILITY - ¾”
CONSTRUCTION - Rugged cast iron motor housing dissipates heat away from motor. Rugged corrosion resistant, molded polypropylene pump body.
MOTOR - 115 volt thermal overload protected, CSA approved continuous duty “oil free” motor. Stainless steel heat treated shaft. Carbon/Ceramic mechanical seal. Upper and lower ball bearings. 6.7 full load amps.
IMPELLER - Reinforced polypropylene, handles ¾" spherical solids - with brass insert.
SWITCH - Automatic with piggy-back mercury free mechanical float switch or vertical float switch. Also available in manual operation.
POWER CORD - 20 ft. power cord.
DISCHARGE - 1½" NPT.
Specifications
|
|
|
BE SERIES Self Priming Effluent Pump
These centrifugal, self-priming effluent pumps are designed for installations with septic tanks in areas with drainage problems. Ideal for pumping out flooded basements, livestock watering, flood irrigation, and general dewatering.
CASING - Cast iron; 1¼" NPT suction & discharge.
PRIMING & DRAIN PLUGS - ¾", garden hose size.
MOTOR - CSA approved and continuous duty rated, higher than NEMA service factor dual compartment motors equipped with stainless steel shaft and automatic thermal overload protection.
BUILT-IN CHECK VALVE - Facilitates fast priming and guards against syphoning action.
IMPELLER - 4 vane, semi-open gray cast iron, with "Blind Hole" for motor shaft protection.
SEAL - Carbon
Specifications
|
|
|
WS SERIES Submersible Effluent Pumps
Ideal for liquid effluent pumping applications, as well as light commercial applications with up to 11/16" diameter solids.
CONSTRUCTION - Motor and pump housing is Cast Iron Class 30.
CORD - Power cord sealed at motor housing. WS50, WS50H and WS100H uses SJOW. WS30 uses SJTW.
IMPELLER - Cast Iron Class 30. Solids handling non-clog impeller. Two vanes on the WS50, WS50H and WS100H. Three vanes on the WS30.
SEAL - Mechanical carbon/ceramic type 6, 5/8 rotary.
SHAFT - Motor shaft is 416 stainless steel.
MOTOR - Oil filled chamber with automatic overload protection, double ball bearing. Capacitor Start designed for hi-torque and is thermally protected with automatic reset (single phase only).
SWITCH - Mercury Free float switch for automatic on-off operation; piggyback style WS30. SJE pump master used on WS50, WS50H & WS100H models.
DISCHARGE - 2" NPT. Adaptor kit for 3" NPT available.
Specifications
|
|
|
WSV SERIES Submersible Sewage Pumps Vortex
CONSTRUCTION - Motor housing, pump volute, and impeller are cast iron.
CORD - 20 foot power cord sealed at motor housing.
IMPELLER - A high capacity cast iron vortex impeller, designed for superior solids handling capabilities. This impeller is able to pass 2" solids by creating a vortex. Solids do not come into contact with the impeller. This provides superior clog free operation.
MOTOR - Powerful CSA approved 115 volt, PSC motor. With thermal overload protection and double ball bearings for reliability.
SWITCH - Mercury Free piggy-back float switch for automatic on-off operation.
DISCHARGE - 2" NPT.
FASTENERS - 304 Stainless steel fasteners throughout, for serviceability.
SEAL - Carbon Ceramic mechanical seal.
SHAFT - 300 Grade stainless steel for corrosion resistance.
Specifications
|
|
|
WS SERIES Submersible Grinder Pump
CONSTRUCTION - Motor and pump housing is cast iron, 1¼"NPT discharge.
CORD - Power cord sealed at motor housing, 20ft., 14/3 SJTW
IMPELLER - Ductile iron, recessed, semi open with pump out vanes for mechanical seal protection.
CUTTER - High chrome steel two blade cutter with hardness of 55 – 58 Rockwell C. Stationary cutter ring can be reversed for extended service. Replaceable without dismantling pump.
SEAL - Hard SILICON CARBIDE seal faces, NBR elastomer for long life abrasion resistance.
SHAFT - Corrosion resistant 410 Stainless Steel shaft.
MOTOR - 2hp, single phase, 230 Volt, 15 FLA, capacitor start oil filled motor with automatic thermal overload and upper and lower ball bearing construction. No special panel required. Can be used with regular piggy back style float switch, rated for
Specifications
|
|
|
EPE SERIES Centrifugal Pumps
POWER - 3600 RPM, single and three phase; JM motors.
PORTS - For air bleeding when priming; for draining to prevent frost damage.
SHAFT FLINGER - Combined with large drain hole in adapter bracket prevents moisture from damaging bearings.
SEAL - Viton with carbon-niresist mechanical seat for use in temperatures
Specifications
|
|
