RENNER Type RM 1
Magnetically coupled centrifugal pumps of building group 1.5 are non-self-priming centrifugal pumps with volute casing. They operate in horizontal position and are built in monobloc design. A magnetic coupling connects the pump to the electromotor and transmits the power of the motor to the impeller.

<< Learn More >>

RENNER Type RM 2D

Magnetically coupled centrifugal pumps of building group 1.5 are non-self-priming centrifugal pumps with volute casing. They operate in horizontal position and are built in monobloc design. A magnetic coupling connects the pump to the electromotor and transmits the power of the motor to the impeller.

<< Learn More >>

RENNER Type RM 2.1
Magnetically coupled centrifugal pumps of building group 1.5 are non-self-priming centrifugal pumps with volute casing. They operate in horizontal position and are built in monobloc design. A magnetic coupling connects the pump to the electromotor and transmits the power of the motor to the impeller.

<< Learn More >>

RENNER Type RM 3.1
Magnetically coupled centrifugal pumps of building group 1.5 are non-self-priming centrifugal pumps with volute casing. They operate in horizontal position and are built in monobloc design. A magnetic coupling connects the pump to the electromotor and transmits the power of the motor to the impeller.

<< Learn More >>

RENNER Type RM 4.5

Magnetically coupled centrifugal pumps of building group 1.5 are non-self-priming centrifugal pumps with volute casing. They operate in horizontal position and are built in monobloc design. A magnetic coupling connects the pump to the electromotor and transmits the power of the motor to the impeller.

<< Learn More >>

RENNER Type RM-Cool

The magnetically coupled centrifugal mini-pump of the RM-Cool type 0.5 is the ideal high-performance cooling system to absolutely reliably remove heat from laser devices and computers and is also used in process engineering and solar energy technology etc.

<< Learn More >>

FLUX Horizontal Centrifugal Immersion Pump Type F 620 S TR

For transferring low flammabiltiy liquids from containers, either open topped or closed.
Consisting of an inner tube and outer tube; the drive shaft is supported within the inner tube. A mechanical seal in ceramic oxide, o-rings in FKM, separates the liquid from bearings and upper shaft. With an open conical impeller. With base plate for horizontal installation. With thread connection on suction and discharge side.

<< Learn More >>

FLUX Vertical Centrifugal Immersion Pump Type F 640 PP/PVDF

For transferring corrosive liquids in the chemical industry and chemical engineering. The centrifugal impeller in the pump housing is driven by the drive shaft supported in the inner tube. A mechanical seal in ceramic oxide/SiC, o-rings in FKM, separates the liquid from bearings and upper shaft. A steel cored inner tube in PP or PVDF provides the ultimate in stability, preventing elongation of the plastic at high temperatures. Range of carefully chosen impeller diameters. 2 sizes: 185 and 230 to meet varying capacity requirements.

<< Learn More >>

FLUX Vertical Centrifugal Immersion Pump Type F 706 PP

For transferring corrosive liquids in the chemical industry and chemical engineering together with any application that requires the safe and economical transfer or circulation of acids and alkalis or other chemical fluids, with or without solids in suspension. With slide bearing, lubricated by the liquid, for immersion lengths up to 2000 mm. Very smooth running, due to a large PP-coated drive shaft and a thick-walled support tube. Very long service life and extended maintenance intervals, even in the case of continuous use. Range of carefully chosen impeller diameters. 4 sizes: 135, 185, 230 and 350 to meet varying capacity requirements.

<< Learn More >>

FLUX Vertical Centrifugal Immersion Pump Type F 716 PP/PVDF

For transferring neutral or corrosive liquids in the chemical industry and chemical engineering, electroplating, steel or stainless steel pickling plants, flue gas decontamination, exhaust air purification, fresh and waste water treatment. Integral three-phase motor with extended, free flying shaft, allowing the pump to use the motor shaft. No seals or bearings in contact with the liquid. Very smooth running, due to robust support tube or support bars solidly connected to the mounting flange. Very long service life and extended maintenance intervals, even in the case of continuous use; suitable for dry running. Range of carefully chosen impeller diameters. With mounting flange for stationary installation. 4 sizes: 115, 135, 185 and 230 to meet varying capacity requirements.

<< Learn More >>

FLUX Vertical Centrifugal Immersion Pump Type F 726 PP/PVDF

For transferring neutral or corrosive liquids in the chemical industry and chemical engineering, electroplating, steel or stainless steel pickling plants, flue gas decontamination, exhaust air purification, fresh and waste water treatment. Version with support bars for extreme operating conditions. Free flying pump shaft without any seals or bearings in contact with the liquid. Very smooth running, even under heavy load, due to robust pump shaft supported in an upper pedestal. Very long service life and extended maintenance intervals, even in the case of continuous use; suitable for dry running. Range of carefully chosen impeller diameters. With mounting flange for stationary installation. 4 sizes: 115, 135, 185 and 230 to meet varying capacity requirements.

<< Learn More >>

NH Series End Suction Centrifugal Pumps

The Monarch NE series end suction centrifugal pumps are constructed using a thick walled cast iron casing, for maximum durability in highpressure application. The back pull-out design allows for easy access to the impeller without disturbing the suction and discharge piping.

<< Learn More >>

NT Series End Suction Centrifugal Pumps

NT Series Rugged cast iron construction provides stability with either belt or coupling drives, while heavy duty single and double row ball bearings allow a minimum of shaft deflection. Shaft is made from one piece, high strength stress proof steel.

<< Learn More >>

ACT SERIES End Suction Centrifugal Pump

Monarch ACT series end suction centrifugal pumps are of frame mount design for either belt or direct drive through a flexible coupling. This allows the option of connecting these pumps to the motor or engine of your choice.

<< Learn More >>